Your Toyota Camry’s rear seat belts can be upgraded by purchasing new assemblies from a Toyota dealer, an aftermarket provider, or a salvage yard. Replace your belts if they are worn or frayed, the locking mechanism isn’t secure, or the belt retractor isn’t working properly. The occupants of your car may get significant injuries in an accident if the seat belts are not working properly.
In This Article...
Step 5
Locate the turning loop bracket by moving up to the shoulder belt’s top. With a socket and ratchet, remove the plastic trim cover and the bolt it is attached to. From the side wall, take the turning loop bracket off.
Step 6
Find the retaining bolt holding the sidewall’s belt retractor in place. With a socket and ratchet, remove the bolt, then take off the belt retractor. From the car, remove the whole belt assembly.
Step 8
By placing the mounting bolt and lining up the anchor loop with the sidewall hole close to the floor, you may affix the new shoulder belts. Use a socket and ratchet to tighten it. Install the mounting bolt and turning loop bracket on the side wall above the roof. Utilizing a socket and ratchet, tighten the bolt.
Step 9
After removing the old belt retractor, place the new one there and line up the mounting holes. With a socket and ratchet, tighten the mounting bolt after inserting it.
Use a torque wrench to tighten each mounting bolt for the seat belt system to 32 foot-pounds. Place the four mounting nuts before assembling the rear bottom seat cushion. Use a socket and ratchet to tighten the bolts, and then a torque wrench to torque them to 14 foot-pounds.
- ratchet wrench
- Set of metric sockets
Can rear seat belts be changed?
The procedure for installing the rear seat belts in trucks, vans, and SUVs like the Toyota Land Cruiser is the same as that used to replace the front seat belts. However, the passenger compartment’s headliner is where you can find the shoulder belt attachment. When removing the headliner, extra care must be taken to avoid damaging the back of the headliner. The service repair manual can again offer advice on the best procedure in this situation.
In passenger vehicles, seatbelt connection points are located at the base of the back seat. Pushing the seat toward the back of the car, close to where it rests on the floor, will allow you to remove the cushion. As you press back on the center of the seat cushion, you should be able to feel the spring tension release. The seat should then be able to be raised and removed from the car so you can get to the seat belt. Use the tool to attach the fasteners with the proper torque once the belt has been replaced.
One of the most crucial things you can do to improve the safety of any vehicle is to replace any seat belts that are worn out or torn. When it could mean the difference between life and death, damage should never be discounted as insignificant.
Can I change a seat belt on my own?
Seat belts are just another piece of equipment in your car. They are likely to deteriorate and stop keeping you safe as the car ages. Before a seat belt malfunction results in significant injury or death, you might want to think about replacing the seat belts if your car is older or has been in a few incidents. Simple steps could potentially save both your and your passengers’ lives.
You should replace your seat belts if your car is ten years old or older. The belt threads can stretch and become loose over time, and the hardware can deteriorate even in a weekend car or vintage car that you don’t drive often.
After a car accident, you’ll probably think about getting a new seat belt. This is usually a good idea because, even after an accident, the seat belt can have sustained damage that isn’t obvious to the human eye. These flaws could cause a catastrophic breakdown in the event of another accident in the future.
Don’t hesitate to replace your seat belts because of the price. Yes, it can cost $150 or more to replace a single seat belt with a professional. But believe us when we say that whatever the cost, it is a bargain when you contrast it with the cost of a hospital stay, surgery, prolonged rehabilitation, etc. Avoid doing it yourself as well. Hire a qualified, professional mechanic instead because if the seat belt you install fails in an accident, you can be held liable for the victims’ injuries.
Of course, we are aware that every driver has financial concerns. The good news is that some manufacturers, like Honda, give lifetime warranties on their seatbelts, while others, like Toyota, only provide coverage for five years or 60,000 miles. Therefore, it is worthwhile to ask the manufacturer if a guarantee is available for your seat belts.
How is a seatbelt taken out of a Toyota Camry?
Instructions
- With a trim stick, remove the plastic trim pieces.
- To reveal the lower 14mm fastener, lift the lid.
- Unscrew the 14mm fastener.
- To reveal the upper 14mm fastener, remove the cover.
- electrical connector disconnected (if present)
- Seat belt assembly can be removed by removing a 10mm bolt.
How much does a Toyota Camry belt cost to replace?
Serpentine belt repair for a Toyota Camry typically costs between $94 and $114. Between $60 and $76 is the expected cost of labor, while between $34 and $39 is the estimated cost of parts. Taxes and other fees are not included in this range, nor are your particular model year or geographic area taken into account.
Toyota seatbelts have a lifetime warranty, right?
If there are problems with the seatbelts or airbags, which is extremely uncommon, this guarantee will pay for all repairs for 60 months or 60,000 miles, whichever comes first.
Can a seat belt’s belt be changed on its own?
Yes, you should replace them, however depending on your car, the maker may do it for you. I’d advise consulting your owner’s handbook to see if your seatbelt is covered by a lifetime warranty since some makes and models have lifetime seatbelt warranties.
How much does a new seatbelt cost?
Typically, the cost of a new seat belt ranges from $20 to $85 for the belt itself and from $100 to $125 for a mechanic to install it.
The actual cost of your seat belt depends on the make and model of your automobile, just like most other auto parts. In a fancy car, replacing the seat belt will undoubtedly cost you more than, say, in an old Toyota Camry.
Another crucial safety aspect that you shouldn’t overlook? auto insurance Jerry has your back if you’re worried about the potential of finding the best policy.
Jerry is an app, so there’s no need to sit across from him at a desk! After signing up, you’ll receive competitive rates from a wide range of leading suppliers in less than a minute. Once you’ve decided, they can even assist you in canceling your old coverage.
Can a seat belt buckle be changed?
The seatbelt buckle is one of the most often utilized components in your car. The catch, which is found on the inside of the buckle, wears out with time. It will eventually stop being able to properly and securely hold the seatbelt. It’s time to go in and learn how to replace seat belt buckle if you discover that your seatbelt is not locking into the buckle properly or if you can pull it away without hitting the release button. It is relatively simple to access the buckle installation in many automobiles. Furthermore, they can also be taken out with basic hand tools. Here are some suggestions to aid you:
Step 1: You must buy a replacement seat belt buckle in order to learn how to repair a seat belt buckle; there are numerous brands available. Replacement seat belt buckles are available from any auto supply store or online. With any luck, if your car is less than a year old, you should be able to quickly get a replacement from the seller or the producer.
Step 2: You must locate the buckle’s mounting location in the vehicle if you want to learn how to replace a seat belt buckle. The seat belt buckle is frequently fastened to the vehicle’s floor with a bolt.
Step 3: You must first detach the bolt, washer, and nut in order to replace the seat belt buckle. This is simply accomplished by using an adjustable wrench to turn the nut to the left. If your car is older, the bolt can be sticky as a result of rust or dirt accumulation. The next best option for some extra turning force if you can’t spin the bolt with an adjustable wrench is to use a torque wrench.
Step 4: The new buckle should be relocated and screwed into place in the final step if you still want to learn how to repair a seat belt buckle. This can be accomplished by using the new bolt, nut, and washer that are supplied with the buckle.
So, below are a few easy steps that will help you learn how to easily replace the seat buckle.
How can a seat belt buckle that won’t latch be fixed?
It is best to examine the seat belt tongue or the “male” connector if the seat belt buckle won’t latch properly or won’t release readily. The tongue may be malformed and will typically need to be replaced.
Pull the seatbelt webbing all the way up to its maximum length and then slowly let go until the belt retracts if the webbing is jammed in the retractor. If the seatbelt won’t retract after being released from the buckle, this will also be quite effective. Just pull out the seatbelt all the way and look to see if anything is caught on it.
How many belts are there in a Toyota Camry?
The accessories in or on the engine of your Toyota Camry are powered by the drive belt(s) by using the engine revs. Your alternator, water pump, air conditioning compressor, and power steering are a few examples.
Most Toyota Camrys feature one or two drive belts, which are sometimes referred to as serpentine belts. The belt can be formed of perishable materials like rubber, neoprene, or urethane and must be flexible to move over pulleys.
The driving belt belt(s) are tensioned and mounted on pulleys. This secures the belt in position and supplies the attachments with the energy they need to function properly. The accessories’ performance could suffer or cease entirely when the belt begins to wear, is damaged, or breaks.
Drive belts for the Toyota Camry should be changed as necessary or at the predetermined service period as specified in the service manual. Drive belts occasionally get damaged or need to be replaced earlier than anticipated, thus it’s advised to check them at every service.
Depending on the form of the drive belt or belts and whether other engine parts must be removed to gain access to replace them, the cost to have a Toyota Camry drive belt or belts replaced ranges from $100 to $400+.
When the drive belt tension has changed and it has to be replaced or rebuilt, you may occasionally hear a noise warning. Your drive belt may be signaling that it requires maintenance if you hear screeching during or shortly after vehicle starts.
