- Manuals
- Brands
- Excalibur Manuals
- Remote Starter
- AL-XX50-EDPB
- Installation manual
Deluxe keyless entry, security, & remote start system
Hide thumbs
-
- Contents
- Table of Contents
- Bookmarks
Table of Contents
-
Table of Contents
-
Installation Considerations
-
Pin Main Wire Harness
-
-
Pink Wire - Ignition #1 (+) Input/Output
-
Orange Wire - Accessory (+) Output
-
Violet Wire - Start (+) Output
-
Pink/White Wire - Ignition #2 (+) Output - Programmable
-
18 Pin Secondary Wire Harness
-
Black Wire - System Ground (-) Input
-
-
Brown/Red Wire - Brake Pedal (+) Input
-
Black/White Wire - Neutral Safety (-) Input
-
Violet/White Wire - Tach Signal Input
-
Brown Wire - Siren (+) Output
-
White Wire - Flashing Light (+) Output
-
White/Black Wire - Flashing Light (-) Output
-
Gray Wire - Hood Trigger (-) Input
-
Green Wire - Door Trigger (-) Input
-
Violet Wire - Door Trigger (+) Input
-
Red/White Wire - Trunk Release / 2Nd Channel (-) Output
-
Black/Red Wire - Light Relay N/O (+/-) Input
-
Green/Violet Wire - Light Relay COM Output
-
White/Red Wire - Light Relay N/C Input
-
Violet/Black Wire - Horn Relay N/O (+/-) Input
-
Blue/Black Wire - Horn Relay COM Output
-
Brown/Black Wire - Horn Relay N/C Input
-
Pin Secondary Wire Harness
-
Pink Wire - 3Rd Channel (-) Output
-
White/Blue Wire - Remote Start Activation (-) Input
-
White Wire - Alarm Arm (-) Input
-
Brown Wire - Alarm Disarm (-) Input
-
Lt� Green/Red Wire - OEM Alarm Arm / CH4 (-) Output
-
Lt� Green/Black Wire - OEM Alarm Disarm / CH5 (-) Output
-
Pin Satellite Relay Port (RED)
-
Wiring Overview Diagram
-
Pin Satellite Relay Port (BLUE)
-
Pin Door Lock/Unlock Port (RED)
-
Pin Backup Battery Port (WHITE)
-
Green Data Port
-
Black Data/Programming Port
-
BLADE Cartridge Port
-
Dual Zone Sensor Ports (WHITE)
-
Window Mount Antenna Module
-
Status Lights
-
Valet / Programming Switch
-
Tach Programming
-
Programming Transmitters
-
Programmable Features
Advertisem*nt
Quick Links
Download this manual
AL-XX50-EDPB
Deluxe Keyless Entry, Security, & Remote Start System
Installation Guide
May 21, 2013
Temporarycover.Colorcoverisinaseparatefi le.
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for Excalibur AL-XX50-EDPB
-
Remote Starter Excalibur AL-1950-EDPB Operation Manual
Oled color 2-way alarm & remote start (28 pages)
-
Remote Starter Excalibur AL-1850-EDPB Operation Manual
Deluxe 2-way alarm & remote start (24 pages)
-
Remote Starter Excalibur AL-1830-EDPB Operation Manual
Deluxe 2-way alarm & remote start (24 pages)
-
Remote Starter Excalibur AL-2020-EDP Operation Manual
Oled 900mhz color 2-way alarm & remote start (28 pages)
-
Remote Starter Excalibur AL-1650-EDPB Operation Manual
Deluxe alarm & remote start (20 pages)
-
Remote Starter Excalibur AL-XX60-EDPB Installation Manual
Deluxe keyless entry, security, & remote start system (16 pages)
-
Remote Starter Excalibur AL-1670-B Operation Manual
Remote start & security (24 pages)
-
Remote Starter Excalibur AL-XX70B Quick Reference Programming Manual
(2 pages)
-
Remote Starter Excalibur AL-1855-EDPB Quick Start Manual
Deluxe 2-way alarm & remote start system (2 pages)
-
Remote Starter Excalibur AL-1775-3DB Operation Manual
2-way deluxe security/keyless remote starter (25 pages)
-
Remote Starter Excalibur AL-2060-EDPB Operation Manual
Oled color 2-way alarm & remote start (28 pages)
-
Remote Starter Excalibur AL-185X-EDPB Operation Manual
Deluxe 2-way alarm (25 pages)
-
Remote Starter Excalibur AL-1870-3DB Operation Manual
Remote start & security perfected (28 pages)
-
Remote Starter Excalibur POWERSPORTS AL-1070-PS Programming Manual
(2 pages)
-
Deluxe keyless entry & remote starter for automatic transmission vehicles only (20 pages)
-
(32 pages)
Summary of Contents for Excalibur AL-XX50-EDPB
- Page 1 AL-XX50-EDPB Deluxe Keyless Entry, Security, & Remote Start System Installation Guide May 21, 2013 Temporarycover.Colorcoverisinaseparatefi le.
-
Page 2: Table Of Contents
Table Of Contents Installation Considerations ��������������������������������������������������������������������������������������� 3 6 Pin Main Wire Harness �������������������������������������������������������������������������������������������� 3 Red & Red/White Wires - Constant Power (+) Input ������������������������������������������������ 3 Pink Wire - Ignition #1 (+) Input/Output �������������������������������������������������������������������� 3 Orange Wire - Accessory (+) Output ������������������������������������������������������������������������ 4 Violet Wire - Start (+) Output ������������������������������������������������������������������������������������... -
Page 3: Installation Considerations
Installation Considerations BEFORE STARTING THE INSTALLATION, READ THIS ENTIRE MANUAL TO FAMILIARIZE YOURSELF WITH ANY INSTALL REQUIREMENTS • BE SURE TO VERIFY EACH CIRCUIT WITH A DIGITAL MULTIMETER • IDENTIFY WHICH CIRCUITS ARE REQUIRED FOR THE VEHICLE IN QUESTION • MOUNT ANY SYSTEM COMPONENTS AND ROUTE WIRING AWAY FROM MOVING PARTS OR PARTS OF THE VEHICLE THAT GENERATE EXCESSIVE HEAT... -
Page 4: Orange Wire - Accessory (+) Output
6 Pin Main Wire Harness (cont’d) ORANGE WIRE - ACCESSORY (+) OUTPUT This circuit is designed to drive accessory circuits like climate control, etc�� It turns on when remote start is activated (slightly earlier than the primary ignition output) and turns off only during engine cranking�... -
Page 5: Violet/White Wire - Tach Signal Input
18 Pin Secondary Wire Harness (cont’d) CONNECTION (Manual Transmission): Connect this to the brake switch wire that shows (-) ground when the parking brake is engaged� VIOLET/WHITE WIRE - TACH SIGNAL INPUT This input provides the engine’s RPM signal to the remote start� This is typically the most reli- able form of engine detection�... -
Page 6: Red/White Wire - Trunk Release / 2Nd Channel (-) Output
18 Pin Secondary Wire Harness (cont’d) RED/WHITE WIRE - TRUNK RELEASE / 2ND CHANNEL (-) OUTPUT This output provides a 250mA negative output when the trunk release/CH2 function is activated by the controller� The output will remain as long as the controller button(s) is held� CONNECTION: Connect this wire to the vehicle’s existing trunk release switch if it is a low current negative circuit�... -
Page 7: Pin Secondary Wire Harness
6 Pin Secondary Wire Harness PINK WIRE - 3RD CHANNEL (-) OUTPUT This output provides a 250mA negative output when the CH3 function is activated by the con- troller� The output will remain as long as the controller button(s) is held� CONNECTION: Connect this wire to any desired add-on accessory that can utilize a negative activation input�... -
Page 8: Wiring Overview Diagram
Wiring Overview Diagram Window-mount Receive / Transmit Module Status Lights 3rd Chan Remote Start Activation (-) Valet Valet Switch - OR - Arm Ala Switch Status Lights Disarm Alar OEM Alarm Arm / CH4 (-) Outp OEM Alarm Disarm / CH5 (-) Output WIRE LEGEND Hard wire connection required Supported via DATA port(s) - Page 9 6 PIN AUX HARNESS 3 PIN SAT� RELAY PORT (RED) 3rd Channel (-) Output - PINK Start (-) Output - GREEN ote Start Activation (-) Input - WHITE/BLUE Constant 12v (+) Output - RED Arm Alarm (-) Input - WHITE Ignition (-) Output - BLUE Disarm Alarm (-) Input - BROWN arm Arm / CH4 (-) Output - LT�...
-
Page 10: Pin Satellite Relay Port (Blue)
3 Pin Satellite Relay Port (BLUE) NOTE: There is no dedicated harness included� Use the RED 3-pin harness for this port� GREEN WIRE - ACCESSORY (-) OUTPUT This provides a 250mA negative output when the large ORANGE accessory wire is active� CONNECTION: If a negative starter circuit is needed, connect this directly to the vehicle’s nega- tive starter circuit�... -
Page 11: Green Data Port
Green Data Port This port provides a direct digital interface for any Omega IntelliKit, OmegaLink interface mod- ule, or other accessories� It can eliminate the need for several wire-to-wire connections� Refer to the wire diagram overview on page 8 to see which circuits are supported by this port and compare them to the data functions available from the interface module�... -
Page 12: Window Mount Antenna Module
Window Mount Antenna Module This system is equipped with an outboard receiver or transceiver (2-way) module� It is designed to be window mounted high on the windshield for optimal performance and range� It is best to mount this module using the double sided stick pad included (be sure to clean glass before adhering)�... -
Page 13: Programming Transmitters
Programming Transmitters Standard Programming: Using this method to program additional or replacement transmitters does not turn on or otherwise affect the Unauthorized Transmitter Alert (UTA) feature� Step 1 Have all transmitters which are to operate the system at hand� Then, turn the ignition “on”� Step 2 Within 5 seconds of turning on the ignition, press the Valet Switch 5 times�... -
Page 14: Programmable Features
Programmable Features PROGRAMMING FEATURES A matrix of all programmable features and their options are on the next page� For detailed infor- mation on each feature, please refer to the operation manual� Use the procedure below to make any necessary changes� Step 1 Turn the ignition key “ON”, then “OFF”... - Page 15 User Feature Programming: Ignition on, off, press valet 5 times # Feature Lock Button Unlock button Trunk button ”START” button 1 Secure Code 1, 0 (default) 2 Last Door Arming On w/o lock On w/ Lock 3 Automatic Rearming On w/o lock On w/ Lock Enhanced Rearm 4 Starter Interrupt Functions...
- Page 16 Temporarybackcover.Colorcoverisinaseparatefile. IM_AL-XX50-EDPB-v2_5/21/2013...
